Skip to Content

CERESIT CT 34 MINERAL DRY

  • Good adhesion
  • Water-repellent and weather-resistant
  • Vapour-permeable (breathable)

Features and benefits

White, mineral smooth plaster for thermal insulation systems and for use as a mineral putty for making smooth surfaces and repairing traditional plasters, inside and outside buildings.

Properties

Description

CERESIT® CT 34 is used to make smooth surfaces on reinforced layers in complex CERESIT Ceretherm thermal insulation systems. The material can also be used to repair traditional cement-lime plasters inside and outside buildings. CT 34 makes thin-layer smooth surfaces on walls and ceilings, completely covering uneven and rough surfaces of reinforced layers, cement plasters and cement-lime plasters. The thickness of the total plaster layer should be up to 5 mm. Available pack size: 25 kg

Documents and downloads

How to use

CERESIT Tiling CE60 LP Instructions Illustration Step 1

CERESIT CT 34 SUBSTRATE PREPARATION

CERESIT CT 34 can be applied to substrates that are even, load-bearing, dry and free from grease, bitumen, dust and other substances that reduce adhesion. It is recommended to prime dry and very absorbent substrates, especially walls made of aerated concrete blocks and silicate blocks with CERESIT CT 17. Then a reinforced layer should be made. Substrates may be additionally painted with CERESIT CT 16 quartz primer.

CERESIT Tiling CE60 LP Instructions Illustration Step 2

APPLICATION OF CERESIT CT 34

Put the contents of the pack into a measured quantity of water and mix until a homogeneous mass without lumps is obtained. Apply the plaster onto the prepared substrate with a metal float. After the material has set, i.e. after about 90 minutes, it should be trowelled with a sponge float. The maximum thickness of the plaster layer is 5 mm. After complete drying, i.e. after about 24 hours, the plaster may be painted. 

CERESIT Tiling CE60 LP Instructions Illustration Step 3

IMPORTANT TO NOTE WHEN USING CERESIT 34

The work should be carried out in dry conditions, with an air temperature and substrate temperature ranging from +5°C to +25°C. It is necessary to protect your skin and eyes. If the material comes into contact with your eyes, rinse them thoroughly with water and seek medical advice. 

Related how to guides

  • How to apply different types of plasters?
    How to apply different types of plasters?
  • How to apply architectural concrete plaster
    How to apply architectural concrete plaster?
  • Fix EPS insulation boards with adhesive mortar?
    How to fix EPS insulation boards with adhesive mortar?
  • Fix EPS insulation boards with PU adhesive?
    How to fix EPS insulation boards with PU adhesive?
  • How to repair mechanical damages in plastered insulation?
    How to repair mechanical damages in plastered insulation?
  • How to prepare the substrate for installation of the insulation layer
    How to prepare the substrate for installation of the insulation layer
  • Decorative plaster with visage stone effect
  • How to cope with bio contamination on facade

Related products

  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-35/SAP_0201IEC014H8/searchResult.productFields.MainImageAltText}
    CERESIT CT 35
    Decorative thin layer plaster for indoor and outdoor applications. Mineral plaster, woodworm lilke structure, grain 2.5 mm or 3.5 mm.
     
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-137/SAP_0201IEC014E4/searchResult.productFields.MainImageAltText}
    CERESIT CT 137
    Decorative thin layer plaster for indoor and outdoor applications. Stone like structure, grain 1.5 mm, 2.0 mm or 2.5 mm.
     
  • ${/content/heliux/adhesive/ceresit/com/en/products/interoir-finishing/product#/ceresit-ct-17-transparent/SAP_0201JAC016G7/searchResult.productFields.MainImageAltText}
    CERESIT CT 17 TRANSPARENT
    Deep penetrating, quick-drying primer for surface reinforcement of all absorbent substrates, suitable for indoor and outdoor areas. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/interoir-finishing/product#/ceresit-ct-17/SAP_0201JAC014F1/searchResult.productFields.MainImageAltText}
    CERESIT CT 17
    Primer for surface strengthening of all absorbent substrates for indoor and outdoor application, prior to fixing ceramic tiles, pouring floors or fixing thermal insulation boards. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-54/SAP_0201IFC014J9/searchResult.productFields.MainImageAltText}
    CERESIT CT 54
    Hydrophobic, vapour permeable paint for buildings’ façades and interiors. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-16/SAP_0201IGC014E8/searchResult.productFields.MainImageAltText}
    CERESIT CT 16
    Dispersion of synthetic resins to prime the substrates for thin layer mineral, acrylic, silicate-silicone, silicone and elastomeric plasters. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-15/SAP_0201IGC014E6/searchResult.productFields.MainImageAltText}
    CERESIT CT 15
    Silicate dispersion composition of potassium and acrylic to prime the substrates for thin layer silicate plasters, putties and paint coats. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-zu/SAP_0201IAC016A1/searchResult.productFields.MainImageAltText}
    CERESIT ZU
    For polystyrene foam and making a reinforced layer; for fixing polystyrene boards and for making a thin layer reinforced with mesh on them when insulating buildings using the light-wet method. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/interoir-finishing/product#/ceresit-ct-29/SAP_0201JDC014G9/searchResult.productFields.MainImageAltText}
    CERESIT CT 29
    Grey, mineral filler to repair traditional plasters and thin-layer “putties” inside and outside the buildings. 

Frequently asked questions