Skip to Content

CERESIT CD 26 Coarse-grained mortar

  • Low shrinkage
  • Waterproof. Inside & outside use
  • Resistant to frost and de-icing road chemicals

Features and benefits

Coarse-grained one component filler to smooth out concrete and reinforced concrete and to fill cracks/voids and repair damaged substrate.

Properties

Description

CERESIT® CD 26 mortar can be applied manually or mechanically, both on vertical and horizontal surfaces. CD 26 is a part of concrete repair system CERESIT PCC, designed for filling cracks/voids, re-profiling balconies as well as for making the complex repairs for various types of cement and reinforced concrete structures. It allows repairing the structures, even when they have been severely damaged due to exploitation or destruction under the influence of mechanical or corrosive factors. Available pack size: 25kg

Documents and downloads

How to use

CERESIT Tiling CE60 LP Instructions Illustration Step 1

SUBSTRATE PREPARATION FOR APPLICATION OF CERESIT CD 26

CERESIT CD 26 adheres to crack-free, load-bearing, clean concrete substrates free from any substances, which may impair adhesion. The substrate should have sufficient compressive strength (concrete class above C12/15) and pull-off strength of minimum 1,0 MPa.

CERESIT Tiling CE60 LP Instructions Illustration Step 2

APPLICATION OF CERESIT CD 26

Preparation of the mortar: The content of the packaging should be poured to the measured amount of clean water and mixed with the slow rotating drill with a mixer until the homogenous mass without lumps is obtained. Then it is necessary to wait 3 minutes and mix the mortar once again.Application of the mortar: Within the pot life the ready mortar should be applied with the trowel on the freshly applied contact layer or poured to the form and it should be properly structured. In case of larger areas it is advisable to use vibration scantlings. The surface of the filler should be smoothed with the steel trowel or with the plastic trowel or sponge within approximately 10–20 minutes. 

CERESIT Tiling CE60 LP Instructions Illustration Step 3

IMPORTANT TO NOTE WHEN USING CERESIT CD 26

Use CERESIT CD 26 only in dry conditions, the temperatures from +5 to +30°C and relative humidity below 80 %. The mortar should be protected against too fast drying caused by the strong insolation, draughts, etc. The mortar should be protected against rain until it dries completely. Then it is recommended to use the scaffolding protection. Fresh stains should be washed with water, whereas the hardened ones should be removed only in a mechanical manner. 

Related how to guides

  • Chemical anchor in hollow masonry
  • Chemical anchor in concrete

Related products

  • ${/content/heliux/adhesive/ceresit/com/en/products/mortars-and-auxiliaries/product#/ceresit-cd-24/SAP_0201VLC013L6/searchResult.productFields.MainImageAltText}
    CERESIT CD 24
    Filler to repair concrete up to 5mm. Cement mortar to smooth out concrete layers. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/mortars-and-auxiliaries/product#/ceresit-cd-25/SAP_0201VLC013L7/searchResult.productFields.MainImageAltText}
    CERESIT CD 25
    Fine-grained one component filler to smooth out concrete and reinforced concrete, to fill cracks/voids and repair damaged substrates. The range of application is from 5 to 30 mm. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/waterproofing/product#/ceresit-cr-166/SAP_0201WJC014B9/searchResult.productFields.MainImageAltText}
    CERESIT CR 166
    2-component flexible slurry, strengthened with fibres and designed for waterproofing and damp-proofing on deformable and non-deformable mineral substrates. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/mortars-and-auxiliaries/product#/ceresit-cd-24/SAP_0201VLC013L6/variation/1054294/searchResult.productFields.MainImageAltText}
    CERESIT CD 24
    Filler to repair concrete up to 5mm. Cement mortar to smooth out concrete layers. 

Frequently asked questions