Concrete repair

CERESIT CD 30
1-component, anti-corrosion protection and contact mortar „2 in 1”

1-component, anti-corrosion protection and contact mortar „2 in 1”.

With corrosion inhibitors
Excellent adhesion to concrete and steel
For concrete class above C12/15

TDS (1)

CERESIT CD 30

en_GL | application/pdf

Find a retailer

We have you covered

Find a retailer

Works Well With

$${/content/heliux/adhesive/ceresit/com/en/products/mortars-and-auxiliaries/product#/ceresit-cd-24/SAP_0201VLC013L6/variation/1054294/searchResult.productFields.MainImageAltText}$

Concrete repair

CERESIT CD 24

Filler to repair concrete up to 5mm. Cement mortar to smooth out concrete layers.

...
$${/content/heliux/adhesive/ceresit/com/en/products/mortars-and-auxiliaries/product#/ceresit-cd-25/SAP_0201VLC013L7/searchResult.productFields.MainImageAltText}$

Concrete repair

CERESIT CD 25

Fine-grained one component filler to smooth out concrete and reinforced concrete, to fill cracks/voids and repair damaged substrates. The range of application is from 5 to 30 mm.

...
$${/content/heliux/adhesive/ceresit/com/en/products/mortars-and-auxiliaries/product#/ceresit-cd-26/SAP_0201VLC013L8/searchResult.productFields.MainImageAltText}$

Concrete repair

CERESIT CD 26

Coarse-grained one component filler to smooth out concrete and reinforced concrete and to fill cracks/voids and repair damaged substrate.

...
$${/content/heliux/adhesive/ceresit/com/en/products/waterproofing/product#/ceresit-cr-166/SAP_0201WJC014B9/searchResult.productFields.MainImageAltText}$

Cement slurries flexible

CERESIT CR 166

2-component flexible slurry, strengthened with fibres and designed for waterproofing and damp-proofing on deformable and non-deformable mineral substrates.

...

Description
How to Use
FAQ

Product Description

CERESIT® CD 30 is used for anticorrosion protection of reinforced bars as well as a contact layer on the concrete and reinforced concrete before the application of other system components. Application of CD 30 between concrete and repair mortar enables the achievement of very good parameters of mutual cooperation at the top layer. CD 30 is part of the concrete repair system Ceresit PCC, which additionally consists of CD 24, CD 25, CD 26.

With corrosion inhibitors
Excellent adhesion to concrete and steel
For concrete class above C12/15
Resistant to frost and de-icing road chemicals
For vertical and horizontal surfaces

packshot-front-pl-ceresit-CD30-1280x1280

How to Use

SUBSTRATE PREPARATION FOR APPLICATION OF CERESIT CD 30

Ceresit CD 30 adheres to crack-free, load bearing, clean concrete substrates, free from any substance, which may impair adhesion. The substrate should have sufficient compressive strength (concrete class above C12/15) and pull-off strength of minimum 1,0 MPa.

APPLICATION OF CERESIT CD 30

The content of the packaging should be poured to the measured amount of clean water and mixed with the slow rotating drill with a mixer. Within the pot life the ready mortar should be applied with the brush on the protruding, cleaned reinforcement. The mortar should be evenly spread to cover the surface of bars. When the first layer becomes hardened, second layer should be applied.

IMPORTANT TO NOTE WHEN USING CERESIT CD 30

Use CD 30 in dry conditions, the temperatures of air and substrate from +5 to +30°C and relative humidity below 80 %. Fresh stains should be washed with water, whereas the hardened ones should be removed only in a mechanical manner. CD 30 contains cement and when mixed with water it causes alkaline reaction.

Frequently asked questions

Ceresit CD 30 is suitable for repairing the following areas: balconies, consoles, columns and load-bearing trusses, covers, etc.

Looking to Upgrade?

Related How-To Guides

View all

Chemical anchor in hollow masonry

Fix metal anchor in hollow masonry substrate.
Chemical anchor in concrete

Fixing metal anchor in in concrete.

CERESIT CD 30 1-component, anti-corrosion protection and contact mortar „2 in 1”

Documents