Skip to Content

CERESIT CR 62 RESTORATION RENDER

  • High salt absorption and retention capacity
  • Open to diffusion (“breathable”)
  • Easy to apply and hydrophobic

Features and benefits

Renovation plaster, specialized for historical buildings

Properties

Description

CERESIT® CR 62 can be used for making base renovation plasters 10-20 mm thick on damp and salt-containing partitions inside and outside the buildings. Recommended to be used on historical and other buildings subject to renovation. Reduces corrosion phenomena, prevents the formation of salt efflorescence and damp spots, allows to obtain a dry surface of building walls. It can be used for full-surface renovation, local repairs as well as filling cavities. Available pack size: 20 kg

Documents and downloads

How to use

CERESIT Tiling CE60 LP Instructions Illustration Step 1

APPLICATION OF CERESIT CR 62

Pour the material into a pot with measured amount of approx. 5 l water and mix with a low speed mixer until a homogeneous mass without lumps is obtained. After stirring leave material for 60 minutes maturing time and stir briefly again. The plaster prepared in this way should be used within 15 minutes. CR 62 can also be prepared and applied with standard plastering machine. The addition of water depends on the machine type and the required consistency.

CERESIT Tiling CE60 LP Instructions Illustration Step 2

CERESIT CR 62 SUBSTRATE PREPARATION

CERESIT CR 62 adheres to all solid, load-bearing, clean, dry and damp substrates, free of substances that may impair adhesion. Existing coats and old, damaged plasters must be completely removed. Rake out loose mortar joints to a depth of approx. 20 mm and then fill with CR 61. Apply mixed CR 60 wart-like up to 5 mm thickness with a surface coverage of approx. 50% of the full surface area. CR 62 should be applied after the rough coat CR 60 has hardened, at least after 24 hours, or on the base plaster Ceresit CR 61, depending on the adopted solution resulting from the salinity of the walls. 

CERESIT Tiling CE60 LP Instructions Illustration Step 3

IMPORTANT TO NOTE WHEN USING CERESIT CR 62

Use CR 62 only in dry conditions and at temperatures of +5°C to +30°C and below 80% relative humidity. Do not mix with other materials, additives or binders. Do not use on gypsum-based substrates or cover with gypsum-based products. All data given was obtained at an ambient and material temperature of +20°C and 65% relative humidity unless specified otherwise. Protect skin and eyes. For professional users. 

Related how to guides

  • Chemical anchor in hollow masonry
  • Chemical anchor in concrete

Related products

  • ${/content/heliux/adhesive/ceresit/com/en/products/mortars-and-auxiliaries/product#/ceresit-cc-81/SAP_0201VGC013L1/searchResult.productFields.MainImageAltText}
    CERESIT CC 81
    Synthetic resin emulsion additive for repair mortars, plasters, adhesive slurries 
  • ${/content/heliux/adhesive/ceresit/com/en/products/mortars-and-auxiliaries/product#/ceresit-cr-61/SAP_0201VNC014C0/searchResult.productFields.MainImageAltText}
    CERESIT CR 61
    For historical and other buildings subject to renovation 
  • ${/content/heliux/adhesive/ceresit/com/en/products/mortars-and-auxiliaries/product#/ceresit-cr-64/SAP_0201VNC014C2/searchResult.productFields.MainImageAltText}
    CERESIT CR 64
    Finishing layer of the renovation façade system 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-cr-55/SAP_0201IFC019R7/searchResult.productFields.MainImageAltText}
    CERESIT CR 55
    Sol-silicate renovation paint formulated with hybrid silicate binder 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-72/SAP_0201IDC014K9/searchResult.productFields.MainImageAltText}
    CERESIT CT 72
    Decorative thin layer plaster for indoor and outdoor applications. Stone like structure, grain size 1.5 mm, 2.0 mm or 2.5 mm .
     
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-54/SAP_0201IFC014J9/searchResult.productFields.MainImageAltText}
    CERESIT CT 54
    Hydrophobic, vapour permeable paint for buildings’ façades and interiors. 

Frequently asked questions