Skip to Content

CERESIT CT 190 MW FLEX

  • Highly resistant to mechanical impacts
  • Flexible, strengthened and resistant
  • High-adhesion to mineral substrates and mineral wool

Features and benefits

For fixing Mineral Wool boards as well as for applying a thin-armoured layer for thermal insulation of buildings in ETICS systems.

Properties

Description

CERESIT® CT 190 mortar is designed to warm up external walls of the buildings by application of external thermal insulation composite system using mineral wool façade boards as well as lamella. It is an element within CERESIT Ceretherm Wool insulation system (ETICS). CT 190 mortar is used for fixing of mineral wool façade boards and for applying the reinforcing protection layer to insulate the newly constructed objects as well as older buildings to be thermo-renovated. Available pack size: 25 kg

Documents and downloads

How to use

CERESIT Tiling CE60 LP Instructions Illustration Step 1

CERESIT CT 190 SUBSTRATE PREPARATION

Fixing mineral wool boards: CERESIT CT 190 shows good adhesion to carrying, compact, dry and clean substrates free from substances decreasing adhesion of surfaces of walls, plasters and concretes. The adhesion to the existing plasters and paint coatings should be checked before starting the application. Armoured layer application: the surface of the boards which are additionally fixed with mechanical anchors should be thoroughly cleaned by means of a brush with loose wool fibres.

CERESIT Tiling CE60 LP Instructions Illustration Step 2

APPLICATION OF CERESIT CT 190

CERESIT CT 190 should be poured into water and stirred until the homogenous mass is obtained. Fixing mineral wool boards: before the application of the adhesive mortar, it is necessary to apply CT 190. The mortar should be applied and then, the board should be pressed to the wall. When CT 190 is set, the boards should be ground with abrasive paper and fixed with mechanical anchors with steel cores. Armoured layer application: before application of the final layer of adhesive to make so called “priming” of the boards with CT 190. After drying of the layer, start to perform the armoured layer with glass fibre mesh, that should be applied on the fresh mortar and smoothed evenly. 

CERESIT Tiling CE60 LP Instructions Illustration Step 3

IMPORTANT TO NOTE WHEN USING CERESIT CT 190

The armoured layer should not be applied on highly insolated surfaces and the applied layer should be protected against rain. Application should be performed in dry conditions with the substrate and ambient temperature from +5 °C to +25 °C. Skin and eyes should be protected. In case of contact with eyes, they should be rinsed with water and a general practitioner should be consulted. 

Related how to guides

  • How to apply different types of plasters?
    How to apply different types of plasters?
  • How to apply architectural concrete plaster
    How to apply architectural concrete plaster?
  • Fix EPS insulation boards with adhesive mortar?
    How to fix EPS insulation boards with adhesive mortar?
  • Fix EPS insulation boards with PU adhesive?
    How to fix EPS insulation boards with PU adhesive?
  • How to repair mechanical damages in plastered insulation?
    How to repair mechanical damages in plastered insulation?
  • How to prepare the substrate for installation of the insulation layer
    How to prepare the substrate for installation of the insulation layer
  • Decorative plaster with visage stone effect
  • How to cope with bio contamination on facade

Related products

  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-16/SAP_0201IGC014E8/searchResult.productFields.MainImageAltText}
    CERESIT CT 16
    Dispersion of synthetic resins to prime the substrates for thin layer mineral, acrylic, silicate-silicone, silicone and elastomeric plasters. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/interoir-finishing/product#/ceresit-ct-17-transparent/SAP_0201JAC016G7/searchResult.productFields.MainImageAltText}
    CERESIT CT 17 TRANSPARENT
    Deep penetrating, quick-drying primer for surface reinforcement of all absorbent substrates, suitable for indoor and outdoor areas. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/interoir-finishing/product#/ceresit-ct-17/SAP_0201JAC014F1/searchResult.productFields.MainImageAltText}
    CERESIT CT 17
    Primer for surface strengthening of all absorbent substrates for indoor and outdoor application, prior to fixing ceramic tiles, pouring floors or fixing thermal insulation boards. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-180/SAP_0201IBC014F6/searchResult.productFields.MainImageAltText}
    CERESIT CT 180
    For fixing Mineral Wool boards for thermal insulation of buildings by means of ETICS and for insulating ceilings of garages. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-74/SAP_0201IDC014L4/searchResult.productFields.MainImageAltText}
    CERESIT CT 74
    Decorative thin-layer plaster for indoor and outdoor applications, stone structure, grain 1.5, 2.0 or 2.5 mm 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-174/SAP_0201IDC014F2/searchResult.productFields.MainImageAltText}
    CERESIT CT 174
    Decorative thin layer plaster for indoor and outdoor applications, stone like structure, grain 1.5 mm or 2 mm. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-15/SAP_0201IGC014E6/searchResult.productFields.MainImageAltText}
    CERESIT CT 15
    Silicate dispersion composition of potassium and acrylic to prime the substrates for thin layer silicate plasters, putties and paint coats. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-175/SAP_0201IDC014F4/searchResult.productFields.MainImageAltText}
    CERESIT CT 175
    Decorative thin-layer plaster for indoor and outdoor applications, woodworm like structure, grain 2 mm. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/product#/ceresit-ct-325/SAP_0201IJC014H2/searchResult.productFields.MainImageAltText}
    CERESIT CT 325
    Reinforcing mesh for Ceresit Ceretherm External Thermal Insulation Composite Systems. 

Frequently asked questions