CERESIT CT 84 EXPRESS STD

  • Ensures speed of execution
  • Up to 10 sqm coverage
  • Superior adhesion to cement-based adhesives

Features and benefits

For fixing expanded and extruded polystyrene plates in Ceresit Ceretherm thermal insulation systems and for fixing other types of insulating plates.

Properties

Description

CERESIT® CT 84 Express is used for fixing expanded and extruded polystyrene plates in CERESIT Ceretherm façade thermal insulation systems. CT 84 can be used to apply polystyrene plates both on the facades of new buildings and on buildings to be thermally rehabilitated by thermal insulation. Available pack size: 850 ml

Documents and downloads

How to use

CERESIT Tiling CE60 LP Instructions Illustration Step 1

CERESIT CT 84 EXPRESS SUBSTRATE PREPARATION

CERESIT CT 84 adheres very well to mineral bearing surfaces. In case of temperatures low temperatures, the surfaces to which CERESIT CT 84 must be protected from frost. The adhesion of existing plaster and paint coatings must be checked beforehand. Any surface contaminated with other non-adherent substances or surfaces with poor adhesion to the substrate must be removed.

CERESIT Tiling CE60 LP Instructions Illustration Step 2

APPLICATION OF CERESIT CT 84 EXPRESS

Shake the tube vigorously for a few seconds, then remove the valve cover, then screw the applicator gun so that the vial to be down the valve. The valve opens by twisting. After screwing the applicator gun, the valve opens and the adhesive can be removed by pressing the trigger. CERESIT CT 84 should be applied with the gun so that the can to be down the valve. When applying polystyrene plates on a previous thermal insulation, CERESIT CT 84 applies on the perimeter. 

CERESIT Tiling CE60 LP Instructions Illustration Step 3

IMPORTANT TO NOTE WHEN USING CERESIT CT 84 EXPRESS

CERESIT CT 84 adhesive allows to lower the temperature below 0°C within 8 hours of application. It contains substances harmful to health. During application, it is recommended to wear glasses and protective gloves should be used. The tube contains compressed flammable gas, therefore you must away from sources of heat and should not be kept in the temperature above +50°C. The tube must not be punctured or thrown into fire. 

Related how to guides

  • How to apply different types of plasters?
    How to apply different types of plasters?
  • How to apply architectural concrete plaster
    How to apply architectural concrete plaster?
  • Fix EPS insulation boards with adhesive mortar?
    How to fix EPS insulation boards with adhesive mortar?
  • Fix EPS insulation boards with PU adhesive?
    How to fix EPS insulation boards with PU adhesive?
  • How to repair mechanical damages in plastered insulation?
    How to repair mechanical damages in plastered insulation?
  • How to prepare the substrate for installation of the insulation layer
    How to prepare the substrate for installation of the insulation layer
  • Decorative plaster with visage stone effect
  • How to cope with bio contamination on facade

Related products

  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/central-pdp#/ceresit-ct-87/SAP_0201IAC014N2/searchResult.productFields.MainImageAltText}
    CERESIT CT 87
    For fixing Expanded Polystyrene (EPS) boards, Mineral Wool boards and for applying a thin armoured layer for thermal insulation of buildings in ETICS systems. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/central-pdp#/ceresit-ct-16/SAP_0201IGC014E8/searchResult.productFields.MainImageAltText}
    CERESIT CT 16
    Dispersion of synthetic resins to prime the substrates for thin layer mineral, acrylic, silicate-silicone, silicone and elastomeric plasters. 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/central-pdp#/ceresit-ct-74/SAP_0201IDC014L4/searchResult.productFields.MainImageAltText}
    CERESIT CT 74
    Decorative thin-layer plaster for indoor and outdoor applications, stone structure, grain 1.5, 2.0 or 2.5 mm 
  • ${/content/heliux/adhesive/ceresit/com/en/products/facade-solutions/central-pdp#/ceresit-thermo-universal/SAP_0201IAC015R0/searchResult.productFields.MainImageAltText}
    CERESIT THERMO UNIVERSAL
    Reinforcing Rendering Mortar - Basic coating XPS, EPS, MW. 

Frequently asked questions

CERESIT CT 84 Express Plus is used for fixing tiles expanded and extruded polystyrene as well as mineral wool, in the CERESIT facade insulation system Ceretherm Express. CERESIT CT 84 Express Plus can be used for the application of polystyrene boards and mineral wool boards on both the facades of new buildings as well as buildings to be renovated.

CERESIT CT 84 can be applied on expanded and extruded polystyrene, mineral wool, wood, OSB, glass, metal, concrete, bituminous surfaces.

CERESIT CT 84 EXPRESS is present in CERESIT Ceretherm EXPRESS System